Scholarlink

Objective <p>To evaluate the effects of commonly consumed staining beverages on the color stability and surface roughness of two additively manufactured permanent resin restorative materials.</p> Materials and methods <p>Sixty disk-shaped specimens (10&#xa0;mm × 2&#xa0;mm) were fabricated from two additively manufactured resin materials (Saremco Print Crowntec and VarseoSmile Crown Plus). Specimens were finished with standardized polishing procedures and color values (CIE L*a*b*) and baseline surface roughness (Ra) were recorded. Samples were randomly assigned to three immersion media (tea, coffee, distilled water; <i>n</i> = 10 per subgroup) and stored at 37&#xa0;°C for 14 days with daily solution renewal. Color measurements were repeated after 24&#xa0;h and 14 days, and color differences were calculated using the CIEDE2000 formula (ΔE₀₀). Surface roughness was re-measured after 14 days. Data were analyzed using mixed-model ANOVA and correlation tests (α = 0.05).</p> Results <p>Staining solution significantly affected color change at both evaluation periods (<i>p</i> &lt; 0.001), while material type had no significant influence (<i>p</i> &gt; 0.05). Tea produced the highest discoloration values, followed by coffee, whereas water groups remained below acceptability thresholds. Color change increased significantly over time in tea and coffee groups. Surface roughness showed only minimal changes after immersion, with Ra values ranging from 0.438 to 0.559&#xa0;μm at baseline and 0.444–0.567&#xa0;μm after 14 days, with no significant effects of material or staining solution (<i>p</i> &gt; 0.05). No significant correlation was found between baseline surface roughness and final color change (<i>p</i> &gt; 0.05). A significant positive correlation was observed between the change in surface roughness (ΔRa) and color change (ΔE00) (<i>p</i> &lt; 0.05).</p> Conclusions <p>Discoloration of additively manufactured permanent resin materials was primarily influenced by exposure to staining beverages. Tea and coffee caused clinically noticeable color changes, while surface roughness showed limited changes during short-term aging. However, a significant positive correlation between surface roughness change and color change suggests that surface degradation may contribute to staining susceptibility.</p>

错误：搜索内容不能为空，请输入英文关键词
错误：关键词超出字数限制，请精简
高级检索

Effect of staining beverages on color stability and surface roughness of additively manufactured permanent resin materials

  • 期刊论文

  • 出版模式：

    开放获取

  • 发表日期：

    2026年5月11日

查看全文
  • Unlu Özge,
  • Sakalli Sedanur,
  • Yildirim Manav Esra

摘要

Objective

To evaluate the effects of commonly consumed staining beverages on the color stability and surface roughness of two additively manufactured permanent resin restorative materials.

Materials and methods

Sixty disk-shaped specimens (10 mm × 2 mm) were fabricated from two additively manufactured resin materials (Saremco Print Crowntec and VarseoSmile Crown Plus). Specimens were finished with standardized polishing procedures and color values (CIE L*a*b*) and baseline surface roughness (Ra) were recorded. Samples were randomly assigned to three immersion media (tea, coffee, distilled water; n = 10 per subgroup) and stored at 37 °C for 14 days with daily solution renewal. Color measurements were repeated after 24 h and 14 days, and color differences were calculated using the CIEDE2000 formula (ΔE₀₀). Surface roughness was re-measured after 14 days. Data were analyzed using mixed-model ANOVA and correlation tests (α = 0.05).

Results

Staining solution significantly affected color change at both evaluation periods (p < 0.001), while material type had no significant influence (p > 0.05). Tea produced the highest discoloration values, followed by coffee, whereas water groups remained below acceptability thresholds. Color change increased significantly over time in tea and coffee groups. Surface roughness showed only minimal changes after immersion, with Ra values ranging from 0.438 to 0.559 μm at baseline and 0.444–0.567 μm after 14 days, with no significant effects of material or staining solution (p > 0.05). No significant correlation was found between baseline surface roughness and final color change (p > 0.05). A significant positive correlation was observed between the change in surface roughness (ΔRa) and color change (ΔE00) (p < 0.05).

Conclusions

Discoloration of additively manufactured permanent resin materials was primarily influenced by exposure to staining beverages. Tea and coffee caused clinically noticeable color changes, while surface roughness showed limited changes during short-term aging. However, a significant positive correlation between surface roughness change and color change suggests that surface degradation may contribute to staining susceptibility.