Scholarlink

<p>Shot peening is a well-established surface treatment that enhances mechanical performance by inducing plastic deformation, grain refinement and compressive residual stresses. This study evaluates the effects of shot peening on wire arc additively manufactured (WAAM) AZ80 magnesium alloy, benchmarked against wrought Al6082 aluminium—a widely used aerospace material. WAAM AZ80 was assessed in two states: a baseline variant (P1) with significant retained process-induced defects, and an improved version (P2) produced via refined processing parameters. Microstructure, hardness, surface roughness, residual stress and fatigue behaviour were systematically analysed. Shot peening induced notable grain refinement in both materials without causing phase transformations. Surface hardness increased by 18% in Al6082, and by 37% and 45% in WAAM AZ80 (P1 and P2, respectively), mainly due to work hardening and grain boundary strengthening. Increased surface roughness was observed across all conditions. Al6082 exhibited peak compressive residual stresses of ~ 280&#xa0;MPa at depths &gt; 100&#xa0;µm, whilst WAAM AZ80 reached ~ 110&#xa0;MPa at ~ 75&#xa0;µm. Fatigue life improved by 44% in Al6082, and by 100–350% depending on the orientation of residual defects caused by the AM process in the WAAM AZ80 (P1) specimens. Shot peening proved effective in mitigating the influence of surface and near-surface defects. Densified WAAM AZ80 (P2) samples also exhibited significantly improved fatigue performance after shot peening, reaching the test run-out of 10<sup>6</sup> cycles without failure. The improvements in WAAM AZ80 are largely attributed to reduced surface-connected porosity and delayed crack initiation. Whilst Al6082 retains superior fatigue properties, shot-peened WAAM AZ80 shows strong potential as a lightweight alternative for weight-sensitive aerospace applications involving cyclic loading.</p>

错误：搜索内容不能为空，请输入英文关键词
错误：关键词超出字数限制，请精简
高级检索

Enhancing fatigue resistance in WAAM AZ80 magnesium and wrought Al6082 through shot peening: a comparative study

  • 期刊论文

  • 出版模式：

    开放获取

  • 发表日期：

    2025年9月2日

查看全文
  • Danjel Grima,
  • Nejmeddine Layeb,
  • Runsheng Li,
  • Brian Zammit,
  • Bonnie Attard,
  • Ann Zammit,
  • Glenn Cassar

摘要

Shot peening is a well-established surface treatment that enhances mechanical performance by inducing plastic deformation, grain refinement and compressive residual stresses. This study evaluates the effects of shot peening on wire arc additively manufactured (WAAM) AZ80 magnesium alloy, benchmarked against wrought Al6082 aluminium—a widely used aerospace material. WAAM AZ80 was assessed in two states: a baseline variant (P1) with significant retained process-induced defects, and an improved version (P2) produced via refined processing parameters. Microstructure, hardness, surface roughness, residual stress and fatigue behaviour were systematically analysed. Shot peening induced notable grain refinement in both materials without causing phase transformations. Surface hardness increased by 18% in Al6082, and by 37% and 45% in WAAM AZ80 (P1 and P2, respectively), mainly due to work hardening and grain boundary strengthening. Increased surface roughness was observed across all conditions. Al6082 exhibited peak compressive residual stresses of ~ 280 MPa at depths > 100 µm, whilst WAAM AZ80 reached ~ 110 MPa at ~ 75 µm. Fatigue life improved by 44% in Al6082, and by 100–350% depending on the orientation of residual defects caused by the AM process in the WAAM AZ80 (P1) specimens. Shot peening proved effective in mitigating the influence of surface and near-surface defects. Densified WAAM AZ80 (P2) samples also exhibited significantly improved fatigue performance after shot peening, reaching the test run-out of 106 cycles without failure. The improvements in WAAM AZ80 are largely attributed to reduced surface-connected porosity and delayed crack initiation. Whilst Al6082 retains superior fatigue properties, shot-peened WAAM AZ80 shows strong potential as a lightweight alternative for weight-sensitive aerospace applications involving cyclic loading.