Scholarlink

<p>The present work investigates the microstructural evolution and mechanical properties in a novel medium-Si 12%Cr reduced activation ferritic/martensitic steel cladding tube (Fe–11.8Cr–0.2C–1.4W–0.17Ta–0.2V–0.55Si–0.5Mn, wt%) during multi-pass cold rolling and annealing. The initial hot-extruded tube exhibited a full martensitic matrix with the prior austenite grain size of ~ 32&#xa0;μm. After annealing, Cr<sub>23</sub>C<sub>6</sub> and TaC particles were precipitated, which are basically unchanged (152–183&#xa0;nm and 84–113&#xa0;nm, respectively) during the manufacturing process. Meanwhile, with the cold-rolling strain (<i>ε</i>) increasing and subsequent annealing, the martensitic lath gradually diminishes, and the recrystallization volume fraction (<i>f</i><sub>r</sub>) is increased. Based on the static recrystallization kinetics model, a clear relationship between <i>f</i><sub>r</sub> and <i>ε</i> is established, in which the newly proposed kinetic equation demonstrates a strong correlation with the experimental results. Furthermore, the yield strength (σ<sub>YS</sub> = 362&#xa0;MPa) of the final annealed state was much lower than that (σ<sub>YS</sub> = 482&#xa0;MPa) of the initial annealed state, which can be attributed to the recrystallization from the martensitic matrix to ferritic matrix. Various strengthening mechanisms are further discussed, and the calculated strengths are in good agreement with the experimental results. This work provides a guidance for the optimization of cold-rolling and annealing treatments in the manufacture of cladding tube.</p>

错误：搜索内容不能为空，请输入英文关键词
错误：关键词超出字数限制，请精简
高级检索

Recrystallization Behavior and Mechanical Property of a Medium-Si 12%Cr Reduced Activation Ferritic/Martensitic Steel Cladding Tube During the Manufacture

  • 期刊论文

  • 发表日期：

    2025年5月17日

查看全文
  • Sen Ge,
  • Ben Niu,
  • Zhen-Hua Wang,
  • Qian-Fu Pan,
  • Chao-Hong Liu,
  • Qing Wang

摘要

The present work investigates the microstructural evolution and mechanical properties in a novel medium-Si 12%Cr reduced activation ferritic/martensitic steel cladding tube (Fe–11.8Cr–0.2C–1.4W–0.17Ta–0.2V–0.55Si–0.5Mn, wt%) during multi-pass cold rolling and annealing. The initial hot-extruded tube exhibited a full martensitic matrix with the prior austenite grain size of ~ 32 μm. After annealing, Cr23C6 and TaC particles were precipitated, which are basically unchanged (152–183 nm and 84–113 nm, respectively) during the manufacturing process. Meanwhile, with the cold-rolling strain (ε) increasing and subsequent annealing, the martensitic lath gradually diminishes, and the recrystallization volume fraction (fr) is increased. Based on the static recrystallization kinetics model, a clear relationship between fr and ε is established, in which the newly proposed kinetic equation demonstrates a strong correlation with the experimental results. Furthermore, the yield strength (σYS = 362 MPa) of the final annealed state was much lower than that (σYS = 482 MPa) of the initial annealed state, which can be attributed to the recrystallization from the martensitic matrix to ferritic matrix. Various strengthening mechanisms are further discussed, and the calculated strengths are in good agreement with the experimental results. This work provides a guidance for the optimization of cold-rolling and annealing treatments in the manufacture of cladding tube.